中国“达标排放”政策的实证分析及理论探讨

以固定点源烟尘排放为例,从排放标准和监测标准两方面讨论了中国现阶段“达标排放”的状况,指出当前的大气污染源达标排放实际上是“初步达标排放”,现在的排放标准和监测规范合适考核污染源的初步达标排放,不适合考核污染源的连续达标排放。排放标准的规定形式、监测规范和适用范围需要改革。现在的排放标准指标需要与监测规范和超标率限值结合起来,以促进污染源的连续达标排放。     

机械强化污泥回流式一体化活性污泥法的运行机理研究

活性污泥通过机械搅拌强化污泥内循环回流,提高了污泥的活性,并且使污泥浓度可达到4.5kg/m3,用该机械强化污泥回流式一体化活性污泥法处理小区生活污水,当水力停留时间为3h,溶解氧为2.2mg/L,机械搅拌速度为250r/min时,CODcr、氨氮去除率均可达到83% 以上,出水达到国家污水排放一级标准.该一体化活性污泥法简单易行,运行成本低,投资小,操作维护方便,是生活小区生活污水适宜的处理工艺技术.     

湖泊水质富营养化评价的多准则神经网络法

提出了基于误差平方和准则与模糊熵准则下的多准则神经网络湖泊水质营养化评价模型，并将其应用于我国五大湖泊水质营养化的评价。结果表明，多准则神经网络用于湖泊水质营养化评价，具有简便，实用，客观和广泛的通用性     

污水处理厂污泥脱水滤液循环利用的研究

对污水处理厂污泥机械脱水滤液进行了循环利用研究。将滤液与剩余污泥（mlsss≤13000mg／l）按1比4的比例均匀混合。然后加入到沉淀器中进行重力浓缩试验，结果表明：它能够改善污泥的浓缩脱水性能，加快污泥的沉淀速度，增大浓缩污泥的浓度；生产运行数据分析显示：污泥脱水滤液与剩余污泥混合液进入浓缩池后，上清液更加清澈，污泥的固体负荷率显著提高，这既可降低污泥的处理成本，亦可减少污泥处理系统的基建投资，为污泥处理系统的工艺优化开辟了新途径。     

海水环境下玻璃纤维增强复合材料力学性能演化规律研究

目的 研究海水环境下海流能发电机组叶片用玻璃纤维复合材料力学性能的变化规律.方法 在实验室内通过海水浸泡试验、拉伸试验、弯曲试验以及剪切试验,测定叶片用玻璃纤维树脂基复合材料的吸水特性,以及在人工海水介质中各项力学性能参数的演变规律.结果 随着浸泡时间的增加,玻璃纤维树脂基复合材料吸水率先逐步增大、后趋于稳定,总吸水率约0.075％.抗拉强度呈先降低、后提高、又降低的趋势,抗拉强度最高可超过1100 MPa,最小值约为940 MPa.弹性模量和弯曲强度呈逐渐降低的趋势,弹性模量降幅约9.5％,弯曲强度降幅约为30％.弯曲模量变化起伏不定,变化幅度在15％以内.材料剪切强度呈先增大、后降低的趋势,最小值为189 MPa,较初始值高10 MPa.剪切模量呈先降低、后提高的现象,在浸泡28 d时,剪切模量最小,为16.4 GPa.结论 玻璃纤维增强树脂基复合材料经过长期海水浸泡后,拉伸及抗剪切性能略有降低,但降幅不大,抗弯性能下降明显,需要在叶片结构设计和强度计算时,充分考虑抗弯性能衰减的负面影响.     

Starch, Poly(lactic acid), and Poly(vinyl alcohol) Blends

Research on biodegradable materials has been stimulated due to concern regarding the persistence of plastic wastes. Blending starch with poly(lactic acid) (PLA) is one of the most promising efforts because starch is an abundant and cheap biopolymer and PLA is biodegradable with good mechanical properties. Poly(vinyl alcohol) (PVOH) contains unhydrolytic residual groups of poly(vinyl acetate) and also has good compatibility with starch. It was added to a starch and PLA blend (50:50, w/w) to enhance compatibility and improve mechanical properties. PVOH (M_W 6,000) at 10%, 20%, 30%, 40%, 50% (by weight) based on the total weight of starch and PLA, and 30% PVOH at various molecular weights (M_W 6,000, 25,000, 78,000, and 125,000 dalton) were added to starch/PLA blends. PVOH interacted with starch. At proportions greater than 30%, PVOH form a continuous phase with starch. Tensile strength of the starch/PLA blends increased as PVOH concentration increased up to 40% and decreased as PVOH molecular weight increased. The increasing molecular weight of PVOH slightly affected water absorption, but increasing PVOH concentration to 40% or 50% increased water absorption. Effects of moisture content on the starch/PLA/PVOH blend also were explored. The blend containing gelatinized starch had higher tensile strength. However, gelatinized starch also resulted in increased water absorption.     

某复合型地铁车站站台防排烟方案研究

在地铁站台火灾中，机械排烟和补风对于有效排出站台烟气至关重要，地铁设计规范要求采用正压送风方式来防止烟气经扶梯和楼梯流入站厅层。对于复合型地铁站台而言，站厅层可能与其它建筑共用，建筑面积较大，难以提供足够的风压进行正压送风。本文利用性能化防火设计方法对多种站台防排烟方案进行研究，并提出了分析流程。本文还针对某实际工程案例验证了这一流程的可行性，并据此选择了一种将机械排烟和补风有机结合的防排烟方案。本文的研究工作对其它类型地铁站台防排烟方案具有参考价值。     

Mechanical Properties with the Functional Group of Additives for Starch/PVA Blend Film

This paper deals with the mechanical properties and degree of swelling (DS) of starch/PVA blend film with the functional groups i.e., hydroxyl and carboxyl group, of additives. Starch/PVA blend films were prepared by using the mixing process. Glycerol (GL) with 3 hydroxyl group, sorbitol (SO) with 6 hydroxyl group, succinic acid (SA) with 2 carboxyl group, malic acid (MA) with 1 hydroxyl and 2 carboxyl group, tartaric acid (TA) with 2 hydroxyl and 2 carboxyl group and citric acid (CA) with 1 hydroxyl and 3 carboxyl group were used as additives. The results of measured tensile strength (TS) and elongation (%E) verified that both hydroxyl and carboxyl group as a functional groups increased the flexibility and strength of the film. Values of DS for GL-added and SA-added films were low. However, DS values of the films added MA, TA or CA with both hydroxyl and carboxyl group were comparatively high. When the film was dried at low temperature, the properties of the films were evidently improved. The reason is probably because the hydrogen bonding was activated at low temperature.     

粉煤灰最大往返剪切作用面上应变破坏标准的应力条件

基于文献[1]提出的最大往返剪切作用面上的液化应力条件和粉煤灰的动三轴试验数据,运用回归分析方法拟合曲线及相关参数建立了粉煤灰的破坏应力条件,并应用F检验法对参数的回归效果进行了检验,检验结果表明参数的回归效果高度显著。得出的破坏应力条件表明初始剪应力与动剪应力的倒数间并不呈线性关系,而是二次多项式关系,这与张克绪所提出的应力条件存在着差异。因此,可初步认为张克绪的液化应力条件不能直接运用于粉煤灰。     

三种强度准则的盐穴应力弹塑性解及参数敏感性分析

为了更安全地建造地下盐穴储气库，采用Hoek-Brown(H-B)，Mohr-Coulomb(M-C)及Drucker-Prager(D-P)3种强度准则，推导了在内压作用下盐穴的塑性区应力解及塑性半径，讨论了各准则对塑性区半径的影响规律及各准则参数的估计方法。分别运用单因素分析法及多因素分析法，分析了塑性半径对H-B准则参数的敏感性。研究结果表明:同等条件下，H-B准则受岩性、造腔等因素影响时，微小内压的波动使得塑性半径的变化更剧烈，岩体质量较差时更显著。盐穴塑性应力与M-C，D-P相比偏小，更接近实际工程状况。围岩塑性半径受H-B准则参数影响程度的大小依次为:GSI，mi，σci，D。各参数的互相关性对结果影响不大。其中，H-B准则参数GSI，mi，σci的增大会使塑性半径减小，参数D的增大使得塑性区半径增大。研究成果可为合理选择盐穴储库硐室的力学模型及优化参数提供参考价值。